Align TREX 500 3G Flybarless System AGNH50123
This is the Align 3G 3-axis flybarless system for the T-Rex 500
Please choose from options menu the following
H50123 500 3G Programmable Flybarless System/Black
H50124 500 3G Programmable Flybarless System Combo/Black

H45109 450 3G Programmable Flybarless System

H25103 250 3G Programmable Flybarless System

GP780 Head Lock Gyro Combo (GP780+DS650)HEG78005
GP780:
Brand new intelligent control logic providing dynamic gain adjustment by detecting current flying conditions, allowing for consistent pirouetting rates during chaos or other demanding 3D maneuvers.
Utilizes feed forward control logic to boost rudder starting speed, and increase response sensitivity.
Utilizes Silicon Micro Machines (SMM) sensor with excellent stability to dramatically reduce in-flight tail drifts.
Utilizes AHTCS (Active Helicopter Tail Control System) to compensate any drift caused by wind direction and force, as well as unintended yaw induced by helicopter itself during flight maneuvers.
Tailor made specifically for use with high speed digital rudder servos. This gyro festures high sensitivity and minimal reaction time, fully utilizing the potential of modern high speed digital rudder servos.
Suitable for all sizes of helicopters, from micro indoor to large 90 size glow helicopters.
Metallic dampening plate built into bottom gyro casing, dramatically increasing anti-vibration and anti-interference abilities.
Features 1520μs pulse wide and 760μs narrow pulse wide frame rate.
Digital/Analog servo switchable.
Reverse switch.
Rudder servo travel limit adjustment (ATV).
Mode switch for large/mini helicopter.
Delay adjustment.
Gyro locking mode and gain can be adjusted remotely from the transmitter.
Mini/Micro heli mode, suitable for T-REX250/450("STATUS" Red);Medium/large heli mode, suitable for T-REX500/600/700("STATUS" Green)
There are 3 kinds of 760μs narrow pulse wide servos on the market, including Futaba S9251, S9256, BLS251.
DS650:
Ultra-speed servo for instant tail control reaction(0.048sec/60 deg).
12 Bits 4096 signal resolution for smooth movements.
Ultra Performance Coreless Motor with fast reaction and low current.
Hardened high strength superalloy gears that increase the lifetime.
Aluminum alloy mid case construction for instantaneous heat dissipation, maintaining servo's high efficiency.
Supports digital & analog control signal.
Powerful and precise servo, suitable for T-Rex 600/700 rudder use.
Specification:
GP780 Ratings:
Operating Voltage:DC 4.5~7V
Current Consumption:<80mA @ 4.8V
Angular Detection Speed:500 degrees/sec
Operating Humidity:0℃~65℃
RoHS certification.
Operating Humidity:0%~95%
Size:26x25x11mm
Weight:14g
DS650 Ratings:
Stall torque:4.0kg.cm(4.8V)
             5.0kg.cm(6.0V)
Motion speed:0.058sec/60°(4.8V)
             0.048sec/60°(6.0V)
Rating voltage:DC 4.8-6V
Temperature range:-20°C~+60°C
Dimension:40.3x20.1x36mm
Weight:56g
1520μs standard band

GP780 Head Lock Gyro Combo (GP780+DS520) HEG78003
DS520:
Coreless Motor Design for fast speed, high efficiency, and low power consumption.
10 Bits signal resolution for smooth movements.
Response time of 0.07s/60°. High strength composite alloy gears with high precision and durable structure characteristics.
Aluminum alloy mid case construction for instantaneous heat dissipation, maintaining servo's high efficiency.
Supports digital & analog control signal.
Powerful and precise servo suitable for T-Rex 500 CCPM cyclic and rudder servo use.
Specification:
GP780 Ratings:
Operating Voltage:DC 4.5~7V
Current Consumption:<80mA @ 4.8V
Angular Detection Speed:500 degrees/sec
Operating Humidity:0℃~65℃
RoHS certification.
Operating Humidity:0%~95%
Size:26x25x11mm
Weight:14g
DS520 Ratings:
Stall torque:1.9kg.cm(4.8V)
             2.5kg.cm(6.0V)
Motion speed:0.09sec/60°(4.8V)
             0.07sec/60°(6.0V)
Rating voltage:DC 4.8-6V
Temperature range:-20°C~+60°C
Dimension:35 x 15 x 29.2mm
Weight:25.9g
1520μs standard ban

GP780 Head Lock Gyro Combo (GP780+DS420)
DS420:
Fast speed and high torque. High strength metal gears with high precision and durable structure characteristics.
Aluminum alloy mid case construction for instantaneous heat dissipation, maintaining servo's high efficiency.
Supports digital & analog control signal.
Precise servo, suitable for T-Rex 250 rudder use.
Specification:
GP750 Ratings:
Operating Voltage:DC 4.5~7V
Current Consumption:<80mA @ 4.8V
Angular Detection Speed:500 degrees/sec
Operating Humidity:0℃~65℃
RoHS certification.
Operating Humidity:0%~95%
Size:26x25x11mm
Weight:14g
DS420 Ratings:
Stall torque:0.75kg.cm(4.8V)
             1.0kg.cm(6.0V)
Motion speed:0.08sec/60°(4.8V)
             0.06sec/60°(6.0V)
Rating voltage:DC 4.8-6V
Temperature range:-20°C~+60°C
Dimension:22.8 x 12 x 25.4mm
Weight:12.7g
1520μs standard band

GP780 Head Lock Gyro HEG78001
Brand new intelligent control logic providing dynamic gain adjustment by detecting current flying conditions, allowing for consistent pirouetting rates during chaos or other demanding 3D maneuvers.
Utilizes feed forward control logic to boost rudder starting speed, and increase response sensitivity.
Utilizes Silicon Micro Machines (SMM) sensor with excellent stability to dramatically reduce in-flight tail drifts.
Utilizes AHTCS (Active Helicopter Tail Control System) to compensate any drift caused by wind direction and force ,as well as unintended yaw induced by helicopter itself during flight maneuvers.
Tailor made specifically for use with high speed digital rudder servos. This gyro festures high sensitivity and minimal reaction time, fully utilizing the potential of modern high speed digital rudder servos.
Features 1520μs pulse wide and 760μs narrow pulse wide frame rate.
Digital/Analog servo switchable.
Reverse switch.
Rudder servo travel limit adjustment (ATV).
Delay adjustment.
Gyro locking mode and gain can be adjusted remotely from the transmitter.

Mini/Micro heli mode, suitable for T-REX250/450("STATUS" Red); Medium/large heli mode, suitable for T-REX500/600/700("STATUS" Green)
There are 3 kinds of 760μs narrow pulse wide servos on the market, including Futaba S9251, S9256, BLS251.
Specification:
Operating Voltage:DC 4.5~7V
Current Consumption:<80mA @ 4.8V
Angular Detection Speed:500 degrees/sec
Operating Humidity:0℃~65℃
RoHS certification.
Operating Humidity:0%~95%
Size:26x25x11mm
Weight:14g

KN920002A Head lock Gyro RCE-550
Features the travel range adjustment of rudder servo(ATV), can avoid the servo running over the travel range of tail control set, to extend the servo life.
Intelligent drift canceling Circuit design, highly precisely figure out the angular velocity inertia, more wide lock range, minimizing rudder neutral position drift when hovering.
Dual Mode: Headlock and Standard Rate Gyro.
Built-in drift cancel circuit.
Temperature compensation circuit.
Dual position Normal/Reverse switch for Rudder operating direction.
Dual gain control.
Apply to analog and most digital servos.
Compatible Futaba PCM/JR SPCM/Hitec QPCM Receivers.

Specification
Voltage:4.2~6V
Power consumption:Approx.33mA
Rating voltage:DC+4~+6V
Temperature range:-5½C~+60½C
Dimension:23.5x21x15mm
Weight:12g

3G Link cable HEP3GF02
3G link cable incorporates PC configuration GUI (graphical user interface) and latest 3G firmware update to improve system stability, and added pirouette compensation to stabilize center point during pirouettes.
Opens up numerous configuration parameters within the 3G system. Pilots can fine tune the system through the PC GUI to suit individual preferences.
Configurable parameters includes options relating to aileron, elevator, rudder, and combined functions.
Provides real time display of radio control signal speed output, so pilot can fine tune the system based on the helicopter response to control sticks relationship display .
Ability to display the current status of parameters in 3G system for setup verification.
Parameter import/export function to allow backup of settings, as well as exchange of parameters with others through internet.

Specification:
Compatible with USB version 1.0/1.1/2.0
Minimum OS requirement:WINDOWS XP/ VISTA/ 7
CD Content:
3G V2.1 Upgrade Software
3G Configuration GUI
USB Driver
Microsoft .NET Framework 3.5 URL
Instruction Manual

Content:
USB 3G Link cable x 1
USB extension cable x 1
Signal Y-adapter x 1
Installation CD x 1

BeastX Microbeast http://www.youtube.com/watch?v=ukJRDyG06TM&feature=related

MICROBEAST has an aluminum composite design casing. Its slight di men sions allow it to be installed in practically any model helicopter. MICROBEAST can be installed horizontally as well as vertically.
The sensory system is based on the newest MEMS technology. Software with sophisticated sensor data processing makes installation in electrical & nitro model helicopters possible.
With an optional adapter cable, MICROBEAST can also be utilized solely as a tail gyro. This is recommended especially for whoever is switching from the conventional paddle system and wants to slowly approach the RIGID operation with the 3 axle solution (3G-Gyro Mode).
The well-thought-out and easy setup goes smoothly with no need of an expensive programming box or computer. This makes it easy to still change a number of settings even at the airfield.
Moreover MICROBEAST's integrated swashplate mixer enables the use of simple remote control systems which do not have their own swashplate mixing (NO-MIX).
MICROBEAST is able to process many types of sum signals (PPM / S-BUS / Spektrum). With the optional Spektrum Satellite Adapter, installation in indoor model helicopters is also possible without a great number of wires.
Updates and advanced setup possibilities (Setups) can be done com fortably with the optional USB interface „USB2SYS" via the BEASTLINK interface. Software for Windows & Mac can be downloaded free at www.BEASTX.com.

Content:
MICROBEAST
Receiver connection cables
Mounting material
Adjust tool
Instruction manual

Optional Accessories:
USB-Interface (settings / update)
Spektrum-satellite adapter*
Tail-Gyro connection cable

Technische Daten:
Operating voltage: 3,5V...8,5 V DC (Lipo 2s possible)
Processor: 32Bit ARM
Analog processing: 17Bit
Sensor technology: 3 MEMS angular rate sensors
Adjustable servo center pulse width:
Tail: 760μs / 960μs / 1520μs
Adjustable servo pulse rate:
Tail: 50 Hz / 165 Hz / 270 Hz / 330 Hz
Swashplate: 50 Hz / 65 Hz / 120 Hz / 200 Hz
Build-in swashplate mixer:
Mechanical / 90° / 120° / 140°
Serial pulse input:
PPM / S-BUS / Spektrum-satellite*
Size: 34 x 25 x 13,5 mm
Weight without cable: approx. 20 g

*(not possible in delivery status)

Does not include FBL head only control unit