The LiPo Safe is bag made of special fire-resistant materials that has the ability to contain a lithium polymer battery fire or charging mishap. place your lithium polymer battery inside the LiPo Safe and extend the charging wires through the top flap. Charge the lipo batteries when they're in the LiPo Safe for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the LiPo Safe's fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the LiPo Safe.
The LiPo Safe is sealed with a thick, industrial strength, Velcro flap. The current LiPo Safe is designed to handle a lithium polymer battery mishap from 1 to 6 lipoly cells (1s to 6s).
Before using the LiPo Safe you must read and understand the LiPo Safe Safety Instructions. We assume absolutely no liability for any damages of any kind - even with proper use. When using the LiPo Safe, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LiPo Safe on a non-flammable surface and in a ventilated area. Avoid damage to the LiPo Safe and not use the LiPo Safe if it is damaged.
LIPO SAFE USING PRECAUTION
Ensure that charger rate is properly set and polarity is correct
Attach charging leads to battery
Place battery in LiPo Safe towards the bottom
Place LiPo Safe on non-flammable surface
Route charge leads through vent at the top seam of the LiPo Safe
Close top flap of LiPo Safe and press hook and loop closure fully closed
Charge battery using proper charging practices
Always practice extreme caution when charging and never leave a charging battery unattended

Glowstart Charger - 240V    L-IRVGSCH1
Used for charging any glow starter

7.2~8.4V Mains Slow Charger (UK) O-TD7/8
The O-TD7/8 is a mains slow charger for 7.2v and 8.4v rechargeable batteries. The charger is fitted with Tamiya compatible output connector. The mains input is 230v 50Hz and the output is 250mA. This charger is produced to meet all European standards. This is a flexible and reliable unit for batteries between 600 and 4000mAh capacity.
   

Pro Peak Quattro LiPo Charger    O-IP2750
Suitable for Charging 1~4 Li-Po Cells
Microprocessor Controlled
Automatic Charge Current
Constant Current/Constant Voltage Charge Regime
Reverse Polarity Protection on Input and Output   
Specification
Dimensions:    88.4 x 54.6 x 22.6mm

Pro-Peak 12v 700mah SLA Chargr O-IP1012
Used for any of the 12 volt tool box batteries.

NE4210902 charger and adapter for Nine Eagles battery NE4918001
Solo Pro & Free Spirit rc helicopters

Hot Seller !

eXtreme-X-605 is the new intelligent multifunction charger which can charge and discharge for Li-ion/Polymer battery, Ni-MH/Cd battery, even Pb battery. It's all-powerful in a way. Comparing with those correlative products in currently market,
eXtreme-X-605 has special features as following:
Microprocessor controlled
Delta-peak sensitivity
individual cell balancing
Li-ion, LiPo and LiFe capable
Ni-Cd and NiMH capable
Large range of charge currents
Store function, allows safe storage current
Time limit function
Input voltage monitoring. (Protects car batteries at the field)
Data storage (Store up to 5 packs in memory)
Battery break in and cycling.
PC analysis via USB cable (software & USB not included)
Input Voltage: 11~18v
Circuit power: Max Charge Power: 50W / Max Discharge Power: 5W
Charge Current Range: .0.1~5.0A
Discharge current range: .0.1~1.0A
Ni-MH/NiCd cells: 1~15
Li-ion/Poly cells: 1~6
Pb battery voltage: 2~20v
Weight: 455g (Net Weight)
Dimensions: 135x80x25mm

One of the latest additions to the Pro-Peak family, the superb new Cavalier EQ is a feature packed micro-processor controlled fast charger with built-in Li-Po balancer. Perfect for charging Li-Po, Ni-MH, Ni-Cd and Lead Acid batteries from any suitable 10~18 volt DC power source.

With a maximum power output of 50W and a variable charge current of up to 5.0A, the Cavalier EQ is not only a remarkably capable charger, but it's also surprisingly simple to use. That clear LCD display is back-lit for ease of use in low light conditions, and keeps you fully informed of charging progress.

Supplied complete with XH ports and TP adaptor board to suit batteries from Impulse, Flight Power, Thunder Power and many other brands with the optional EH and PQ boards. Includes crocodile/4mm bullet input connectors for easy connection to a 12v battery or DC power supply. The versatile Cavalier EQ can be further expanded with an optional temperature sensor.
Charging Information:

• Battery Charge Rates:
• Li-Po – 1~5 cells
• Ni-MH/ Ni-Cd – 1~14 cells
• Lead Acid (Pb) – 2~12v
• Charge Rate – 0.1~5.0A
• Circuit Power: 50W max
• Charge Current: 0.1~5.0A
• Current Drain (for Li-Po balancing) 200mAh/cell 
• Dimensions:130 x 98 x 30mmVoltage:10.0v to 18.0V (Input)
• Weight:360g
  

A micro processor controlled balance charger that can charge 1 – 5 cell Li-Po packs or 1 – 14 cell Nicad/Nimh packs plus 2-12v Lead acid. Input voltage is 10-18v DC. Charging current range is 0.1A – 5A with a total circuit power limit of 50W.

The built in Li-Po balancer ensures that you keep your Li-Po batteries in top condition. Standard balance sockets/board supplied suit XH and TP with optional balance boards for EH and PQ available. Individual cell votages can be monitored during charging. Li-Po balance current is 200mA.

All this is built into a durable, blue anodised, aluminium case with a clear LCD display screen and simple programming steps.
Options – EH and PQ adaptor boards, Temperature sensor.
The charge lead set in the instructions is not included as standard.

• Width:90mm
• Length:130mm
• Height:28mm
• Weight:350g

Sky RC Imax B6 Balance Charger Special !!!
The new IMAX B6 (successor of IMAX B5) is a very advanced microprocessor controlled charger able to charge, balance and discharge Lion, LiPo, LiFe (A123), Pb, NiCd and NiMH batteries. Significant improvements includes:
Support new generation A123 system (LiFe) battery.
Thermal probe: the most important safety feature to avoid fire and explosion.
Charge up to 6 cells: allow charging of 6S and (multi) series charging of 2X3S or 3X2S.
Store function charge up lipo for recommend store voltage for long time and protect useful time of the battery.
Time limit function
Input voltage monitoring. (Protects car batteries at the field).
Items included:

• 1 x IMAX B6 LiPo battery balance charger
• 1 x Multi-functional extension wire
• 1 x Universal crocodile clip
• 1 x JST plug
• 1 x Receiver plug
• 1 x English manual

• Input Power: 11-16V DC 10Amp at maximum charge rate
• Memory profile: 25Memory for each Battery type
• Charge battery type: LiPoly/NiMH/NiCd/Pb/A123
• Charge voltage and cells:
• LiPoly battery: 1 - 6 cells
• CC to CV change voltage: 4.1BV/cell
• Full Charge Voltage 4.2 V/Cell
• NiMh, NiCd Battery: 1 - 14 cells
• Pb(SLA) battery: 6V/12V/24V
• A123 Battery: 1 - 6 cells
• CC to CV change voltage: 3.0V /Cell
• Full charge voltage: 3.65 V/Cell
• Charge Current: 0.2.5 A, 10A
• Charge control type Lipoly/Al23:CC/CV
• Charge NiCd/NiMH: constant current - delta peak
• Charge/discharge cycles: 9 cycles
• Discharge rate: 50mA - 1 Amp
• Discharge capacity: 7 Watt (Max 1A)
• Capacity display: O-9999mAh
• Timeout limit: 2-10 hour (User selectable)
• Display Tolerance: 0.5%
• Display Type: Backlit 2 x 16 dot LCD
• Charge maximum output 80 Watt
• Output Charge Terminal: 4mm standard banana jack
• Input wire: 16 AWG silicon Wire with attached alligator clips
• Size: 118 x 85 x 28 mm (4.65 x 3.4 x 1.1 in)
• Weight: 205g (9.4oz)

High efficiency alternating current (A/C) power source, rated at 100-240V.
Distributed balancing charging ensures automatic cell balancing, and effectively prevents overcharging or undercharging of individual cell.
Automatically compensates for undervoltage during charging to realize batteries full capacity potential.
Dual battery charging system. LCD charging status display for voltage, current, charge capacity, and individual cell voltage display.
Automatic Initial Charging function which detects excessively discharged cells and attempts initial charging to revive the cells.
Auto control cooling fan.
Reverse polarity and short circuit protection
Specification
Input Voltage: AC 100V~240V(50/60Hz)
Supported Battery Type: Lion or Li-polymer(3.6V/3.7V 1~6S Battery Pack)
Charging Method: CC/CV (Constant Current/Constant Voltage)
Charging Current: 0.1A~4.0A(100W max)
Charging Time Display: 0~9 hours and fifty nine mins
Charging Capacity Display: 0~9999mAh
A、B Battery Status Indicator: CHG. / Full / Ready / Error
Battery Voltage ≦2.5V： LCD Displays Error
2.5V< Battery Voltage < 3.0V: Attempts Initial Charging on Batteries(LCD Displays CHG.)
Battery Voltage ≧4.19V,Charging Current<0.3A: LCD Displays Full
Size:173x112x66mm
Weight:810g

Great for a huge variety of battery types(NiCd, NiMH, LiPo, Li-Ion, and lead-acid), andapplications such as electric airplane and helibatteries, Tx and Rx batteries, car and boatbatteries, field batteries, and more. Triton2adds upgraded features to the design of therevolutionary original Triton charger, famousfor its high performance, versatility and ruggeddurability. Charge current is increased to 7A. Thecustom LCD now includes a blue backlight for easy viewing. T2 can handle LiPo packs with up
to 5 cells in series. The input cord has installed banana plugs and large attachable alligator clips are included. The modified programming dial is easier to control. And a slight programming change, plus a totally new instruction manual for ease of use and understanding.

This is the Bantam Hobby Technology E-Station BC6-10. The E-Station BC6-10 is a microprocessor controlled high performance rapid charger and discharger for NiCD, NiMH, Lithium Polymer and Pb batteries. The E-Station BC6-10 features easy to operate programming. All of the basic factors are optimized and pre-programmed for easy operation and maximum safety. The BC6-10 employs a high-quality aluminum outer case that is durable and efficient to cooling internal heat.

Delta-peak sensitivity: The automatic charge termination program works on the principle of the Delta-peak voltage detection. (NiCd/NiMH)

Auto-charge current limit: When charging NiCd or NiMH at 'AUTO' current mode, you can set the upper limit of charge current to avoid from feeding high current to the battery. This is very useful when charging the low impedance and small capacity NiMH battery in 'AUTO' mode.

Capacity limit: The charging capacity always calculated by multiple of the charging current and time. If the charging capacity exceeds the limit the process will be terminated automatically when you set the maximum value.

Temperature limit: The temperature of the battery on charging will rise by its internal chemical reaction. If you set the limit of temperature the process will be expired forcibly when the limit has been reached.

Processing time limit: You can also restrain the maximum processing time to prevent from any possible defect.

Input power monitor: To protect the car battery using as input power from being damaged, its voltage always being monitored. If it drops below the lower limit the process will be ended automatically.

Automatic cooling fan: The electric cooling fan comes into action automatically only when the internal temperature of the unit is raised.
Specifications:

• Operating voltage: DC 11~18 volts
• Idle Current: approx. 100mA
• Charge/Discharge Power: max 200/25W
• NiCd/NiMH: 1~18 cells
• Li-polymer: 1~6 series
• Pb: 2~24V
• Charge current: 0.1 to 10A
• Discharge current:0.1 to 5A
• No. of cycle: 1 to 5 times
• Battery Data Memory: up to 10 data
• Weight: 960g
• Dimension: 160x120x40mm

Tx/Rx 4 Output Delta Peak Chg 600mA P-FBC40D/4
Are you charging two or three models to fly this weekend? Chances are you are familiar with the scene above... a great jumble of plugs, chargers and wires! And now the solution - the Pro-Peak 4 output charger. Designed for simultaneously charging up to three Ni-Cd or Ni-MH receiver packs and a transmitter, it features Delta Peak charge termination and 1.5m long output leads.
This has to be the most useful and practical R/C charger around!

Input Voltage: 110 - 240V AC
Tx output – 9.6v 600mA
RX outputs (3) – 4.8-8.4v 600mA